PVA-02126N
Revised 01-04
Section 78
Analog Gages PVA20
00-02-0532
& PVA35 Installation Instructions
Please read the following information before installing. A visual inspection of this product for damage during ship-
ping is recommended before mounting. It is your responsibility to have a qualified person install this unit.
GENERAL INFORMATION
WARNING
BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT
✔ Disconnect all electrical power to the machine.
✔ Make sure the machine cannot operate during installation.
✔ Follow all safety warnings of the machine manufacturer.
✔ Read and follow all installation instructions.
PVA35 Series
PVA20 Series
Specifications
Description
Power Supply Input Voltage: 12/24V (8-32VDC min. & max. voltage).
CAUTION: These instruments are designed to be used ONLY
†
with the MurphyLinkTM PowerView module or other approved
Power Supply Operating Current: (@ 14 VDC) =
PVA20, PVA35: 28 mA minimum; 52 mA maximum.
PVAA20: 19 mA minimum; 46 mA maximum.
MurphyLinkTM† PowerView products.
Backlight Maximum Current (not applicable to PVAA20): 24 mA.
Input: RS485 MODBUS® RTU data.
The PowerView Analog Gages (PVA) are a series of intelligent gages
designed to display easy-to-read information transmitted by the PowerView.
The PVA gages communicate with the PowerView via a single RS485 twist-
ed pair MODBUS®† RTU serial link. The gages can be daisy-chained using
quick-connect harnesses with watertight connectors.
Output: Analog Readout.
Relay Rated Load (PVAA20): 0.5 A, 125 VAC; 1 A, 24 VDC.
Relay Maximum Switching Capacity (PVAA20): 62.5 VA, 30W.
The PVA gages also include features such as a smooth stepper motor opera-
tion for the 270° sweep pointer, an environmentally sealed case with two
Deutsch DT style connectors molded into the casing, and green LED back
lighting. They are available for standard 2-1/16 in. (52 mm) and 3-3/8 in. (86
mm) diameter hole sizes. In addition their plastic cases incorporate a “D”
shape allowing panel cutouts that eliminate gage rotation during installation.
External Audible Alarm Output (PVAA20): 28 VDC, 30 mA max. (cur-
rent sink).
Temporary Silence Button (PVAA20): Charge transfer technology.
Operating Temperature: -40° to 185°F (-40° to 85°C).
The PowerView Audible Alarm (PVAA) alerts operators to fault conditions Storage Temperature: -76° to 185°F (-60° to 85°C).
via piezoelectric alarm and relay contacts. It also has a temporary silencer
button that silences the audible tone for 2 minutes on alarms and 30 seconds
on shutdown conditions.
Dial: White numerals over black background.
Indicating Pointer: Stepper motor operation with 270° sweep.
Gage Accuracy: PVA20: Better than ±1.0% of scale.
All PowerView Gages can be powered by 12 or 24 VDC systems.
PVA35: Better than ±2% of scale.
PVA20 Series Models: 2 inch size gages:
Environmentally Sealed Enclosure:
PVA20 –A
PVA20 –B
PVA20 –C
PVA20 –D
PVA20 –E
PVA20 –F
PVA20 –G
PVA20 –T
PVAA20
=
=
=
=
=
=
=
=
=
Engine Oil Pressure
Coolant Temperature
Voltmeter
Percent Load at Current RPM
Transmission Oil Pressure
Transmission Oil Temperature
Engine Oil Temperature
Tachometer
Sealing: IP68, ±5 psi (±34.4 kPA).
Case and Clamp Material: Polyester (PBT).
Lens Material: Polycarbonate.
Bezel Material: Polyester (PBT).
Maximum Panel Thickness: 3/8 in. (9.6 mm).
Connectors: 6-Pin Deutsch DT06 Series.
2 inch dial audible alarm gage
†MurphyLink is a registered trademark of FWMurphy. All other trademarks and
service marks used in this document are the property of their respective owners.
PVA35 Series Models: 3-1/2 in. size gages:
PVA35 –T
PVA35 –S
=
=
Tachometer
Speedometer
PVA-02126N page 1 of 4
PVA20, PVA35 and PVAA SERIES Typical Wirings For 12 and 24 VDC
WARNING: Disconnect battery negative cable before wiring or service. Devices containing solid state components can be damaged or caused to
malfunction when used in systems which incorporate inductive loads (e.g. relays, solenoids, etc.) that can generate voltage spikes. To reduce the
potential for this type of damage, install a fly back or clamping diode across all inductive loads. Use Murphy diode package 65-00-0343 or equivalent.
A typical diode is 1N4005 and is readily available from commercial sources. Failures of this type are not covered by our Limited Warranty.
PowerView Gages Back View
Deutsch DT06-6S Style Connections
RS485 (+) Data
Pin 3
PV100
RS485 (+) Data
RS485 (-) Data
120 ohms
Pin 4
Pin 4
See Note
RS485 (-) Data
Pin 3
PVA Gage
Pin 2
To Next
PVA gage
4
3
A
3
B
Pin 6
4
6
Pin 1
GRND
V+
V+
1
1
GRND
6
Note: Place Resistor between RS485+ and RS485– at end
of Line on last PVA gage (included in PVJR or factory purchased panels).
IMPORTANT: To eliminate external interference: RS485(+) and RS485(-) should be twisted pair cable or twist wires together, one twist per
inch minimum. (RS485 wire for example: BELDEN 9841 or 3105A).
PVAA Audible Alarm Back View
Deutsch DT06-6S Style Connections
RS485 (+) Data
Pin 3
PV100
RS485 (+) Data
RS485 (-) Data
120 ohms
Pin 4
See Note
RS485 (-) Data
PVAA
Audible
Alarm
To Next
PVA gage
4
6
3
A
3
1
B
4
6
5
V+
V+
Pin 1
Pin 6
GRND
1
GRND
V+
Ignition
Switch
5
–
+
+
Optional
Optional Alarm
Horn or Power
Relay Coil
External Alarm
or FWMurphy
–
®
Mini-Siren SAH
V+
Note: Place Resistor between RS485+ and RS485– at end
of Line on last PVA gage (included in PVW-P or factory purchased panels).
Battery
PVA-02126N page 3 of 4
Typical Connectors PIN Designation
PowerView Gages Back View
Deutsch DT06-6S Style Connections
PowerView Audible Alarm Back View
Deutsch DT06-6S Style Connections
Plug A
Plug B
Plug A
Plug B
PIN 3 RS485 +
PIN 3 RS485 +
PIN 4 RS485 –
PIN 4 RS485 –
PIN 3
RS485 +
PIN 3
RS485 +
PIN 4
RS485 –
PIN 4
RS485 –
PIN 2
Relay
COM
PIN 5
Relay
N.O.
PIN 2
Relay
N.C.
PIN 5 Ext.
Audible
Alarm
A
B
A
B
PIN 6
GRND
PIN 6
GRND
PIN 1
V+
PIN 1
V+
PIN 6 GRND
PIN 6 GRND
PIN 1 V+
PIN 1 V+
Recommended Connectors:
Body: Deustch DT06-6S
Wedge Lock: W6S
Recommended Connectors:
Body: Deustch DT06-6S
Wedge Lock: W6S
Terminals: 0462-201-16141
Sealing Plug: 114017
Terminals: 0462-201-16141
Sealing Plug: 114017
Typical Quick-Connect Diagram
Last PVA Gage or
PVAA Audible Alarm
To optional
external device
To Engine
ECU
To PVAA
B
A
Audible Alarm
Terminating
Resistor PVJR
To Battery
Power
Relay N.O.
Relay N.C.
B
A
POWERVIEW
PV100
Ext.
Sonalert
OR
Relay Comm.
Optional PVW-A wire harness
(includes terminating resistor)
Customer provided wire
harness or CAN extension
harnesses or power
B
A
extension harnesses.
PVA Gage
Next PVA Gage
Wire harness
PVW-J
External Dimmer
Wire 24 inch.
B
B
A
A
External
Dimmer
B+
GRND
CAN SHLD
–
CAN LO
–
CAN HI
–
Wire harness PVW-P
Wire harness PVW-J
Wire harness PVW-J
Warranty
A limited warranty on materials and workmanship is given with this FW Murphy product.
CONTROL SYSTEMS & SERVICES DIVISION
P.O. Box 1819; Rosenberg, Texas 77471; USA
+1 281 633 4500 fax +1 281 633 4588
e-mail [email protected]
FRANK W. MURPHY, LTD.
Church Rd.; Laverstock, Salisbury SP1 1QZ; U.K.
+44 1722 410055 fax +44 1722 410088
e-mail [email protected]
MACQUARRIE CORPORATION
1620 Hume Highway
Campbellfield, Vic 3061; Australia
+61 3 9358 5555 fax +61 3 9358 5558
e-mail [email protected]
FW Murphy
P.O. Box 470248
MURPHY DE MEXICO, S.A. DE C.V.
Blvd. Antonio Rocha Cordero 300, Fracción del Aguaje
San Luis Potosí, S.L.P.; México 78384
+52 444 8206264 fax +52 444 8206336
Villahermosa Office +52 993 3162117
e-mail [email protected]
MURPHY SWITCH OF CALIFORNIA
41343 12th Street West
Palmdale, California 93551-1442; USA
+1 661 272 4700 fax +1 661 947 7570
e-mail [email protected]
Tulsa, Oklahoma 74147 USA
+1 918 317 4100
fax +1 918 317 4266
e-mail [email protected]
USA–ISO 9001:2000 FM 28221
UK–ISO 9001:2000 FM 29422
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.
Printed in U.S.A.
PVA-02126N page 4 of 4
|